基于Drucker-Prager准则的扩孔器单齿正交切削岩土三维力学模型

›› 2013, Vol. 34 ›› Issue (5): 1429-1436.

基于Drucker-Prager准则的扩孔器单齿正交切削岩土三维力学模型

贾彦杰，蒋平，童华

西南石油大学机电工程学院，成都 610500

收稿日期:2012-10-29 出版日期:2013-05-10 发布日期:2013-05-14
通讯作者: 童华，女，1979年生，博士研究生，副研究员，主要从事管柱力学与岩土力学等方面的研究工作。E-mail: tonghua@swpu.edu.cn E-mail:jiayj007@foxmail.com
作者简介:贾彦杰，男，1983年生，博士研究生，主要从事岩石岩土力学与切削破碎数值模拟等方面的研究工作。

3D mechanical modeling of soil orthogonal cutting under a single reamer cutter based on Drucker-Prager criterion

JIA Yan-jie，JIANG Ping，TONG Hua

School of Mechanical Engineering, Southwest Petroleum University, Chengdu 610500, China

Received:2012-10-29 Online:2013-05-10 Published:2013-05-14

摘要/Abstract

摘要： 扩孔器是定向穿越扩孔钻进阶段进行岩土切削的主要工具，合理的结构设计是提高扩孔时效、降低工程复杂问题出现几率的主要手段，且由于扩孔阶段是决定定向穿越工程工期的最主要阶段，因此，对扩孔器切削齿的切削效率进行深入研究是非常必要的。从单齿正交切削岩土的机制入手，综合考虑岩土与切削齿面之间的接触摩擦及岩土剪切区的剪切作用，分析了单齿正交切削岩土的力学特征，基于能够考虑中间主应力对岩土破坏影响的Drucker-Prager强度准则，推导了单齿正交切削岩土的主切削力与主切削力矩计算公式；在利用有限元计算程序对所推导公式进行验证的基础上，优选了剪切角计算模型，获得了不同岩土材料时的主切削力解析解，并分析了不同齿前角对主切削力的影响规律，从而获得单齿正交切削岩土的最优齿前角，为进一步研究扩孔器整体结构设计并针对不同岩土介质设计出适应性更强的扩孔器结构奠定基础。

关键词: 正交切削, 岩土力学, 定向穿越, 扩孔钻进, Drucker-Prager强度准则

Abstract: Reamers have been the major implements used to enlarge the hole size in reaming stage of horizontal directional drilling (HDD). The choice of its available structural design becomes critical to maximize the rate of penetration and minimize the tripping time; thereby decreasing the cost of operations and the risk of experiencing stability problems. Moreover, because the duration period of a HDD project is largely dependant on the reaming stage; it is crucial to study the reaming efficiency by use of the appropriate operating conditions (cutting angle and depth). The reaming efficiency of reamer is analyzed based on the development of a 3D analytical cutting force model of soil orthogonal cutting under a single reamer cutter. Focusing on the soil orthogonal cutting mechanism under a single reamer cutter, the interaction and friction between soil and cutter and the shear action of 3D shear zone are comprehensively considered, consequently the mechanical properties are given. Based on these analyses and using the Drucker-Prager criterion given a weight to the intermediate principal stress, the analytical models are proposed. In addition, this paper presents 3D FEM simulations for the analysis of soil orthogonal cutting under a single reamer cutter. The subject has been covered in two parts. Part one deals with the verification of the analytical cutting force model, the other focuses on the assessment and selection of the criterions of shear angle. The analytical cutting force model presented provides the capability to evaluate cutter loading for utilization of a single cutter with different rake angles to cut soils, and to plot the effect of change in the rake angle. Finally, the optimum rake angle of single reamer cutter was obtained. The results of this analysis can be integrated to study reamer performance. It can also provide a guideline to the application and design of the reamer assembly for various soils.

Key words: orthogonal cutting, rock and soil mechanics, directional drilling, reaming process, Drucker-Prager criterion

中图分类号:

U 452

贾彦杰，蒋平，童华. 基于Drucker-Prager准则的扩孔器单齿正交切削岩土三维力学模型[J]. , 2013, 34(5): 1429-1436.

JIA Yan-jie，JIANG Ping，TONG Hua. 3D mechanical modeling of soil orthogonal cutting under a single reamer cutter based on Drucker-Prager criterion[J]. , 2013, 34(5): 1429-1436.

参考文献

相关文章 15

[1]	何春灿，胡新丽，龚辉，谭福林，章涵，张小勇，. 基于软硬石模板库的土石混合体细观损伤与力学特性分析[J]. , 2016, 37(10): 2993-3002.
[2]	陈洪凯，唐红梅，唐云辉，谭玲，魏来，何晓英，高阳华,. 强降雨作用下强风化泥岩降雨入渗特性试验研究[J]. , 2014, 35(10): 2755-2760.
[3]	张雄，陈胜宏,. 预应力锚索损伤软化精细有限元模型[J]. , 2014, 35(10): 3013-3020.
[4]	石崇，王盛年，刘琳，陈鸿杰 . 基于数字图像分析的冰水堆积体结构建模与力学参数研究[J]. , 2012, 33(11): 3393-3399.
[5]	林大超，安凤平，郭章林，张立宁. 滑坡位移的多模态支持向量机模型预测[J]. , 2011, 32(S1): 451-0458.
[6]	金长宇，张春生，冯夏庭. 错动带对超大型地下洞室群围岩稳定影响研究[J]. , 2010, 31(4): 1283-1288.
[7]	孙强，薛雷，王媛媛. 克里金参数估值法及其在参数估计分析中的应用[J]. , 2009, 30(S2): 371-373.
[8]	徐光苗，罗文静，伍永胜. 广州飞碟训练中心高边坡稳定性分析[J]. , 2009, 30(S1): 190-194.
[9]	彭芳乐，高伟，清住真，大内正敏. 钙质石灰岩中桩基轴向承载特性的有限元分析[J]. , 2009, 30(9): 2792-2798.
[10]	张玉军. 孔隙气压对核废物地质处置热-流-固耦合影响的有限元分析[J]. , 2009, 30(5): 1451-1457.
[11]	苏国韶，宋咏春，燕柳斌. 高斯过程机器学习在边坡稳定性评价中的应用[J]. , 2009, 30(3): 675-679.
[12]	刘晓，唐辉明，刘瑜. 基于集对分析和模糊马尔可夫链的滑坡变形预测新方法研究[J]. , 2009, 30(11): 3399-3405.
[13]	姜晨光，李少红，贺勇，张清峰，姜勇，. 地下水位变化与库岸滑坡体稳定性关系的研究[J]. , 2008, 29(S1): 403-406.
[14]	黄诚，杨春和，王安明. 利用全概率方法分析岩土力学数值模拟结果的变异性[J]. , 2008, 29(11): 2919-2926.
[15]	张玉军. 热-水-应力耦合条件下三项因素对核素迁移影响的有限元分析[J]. , 2008, 29(10): 2599-2605.

Metrics

Viewed

Full text

Abstract

Cited

Shared

Discussed