定向射孔压裂起裂与射孔优化设计方法研究

›› 2013, Vol. 34 ›› Issue (8): 2309-2315.

定向射孔压裂起裂与射孔优化设计方法研究

陈峥嵘^{1, 2}，邓金根¹，朱海燕¹，董光¹，胡连波¹，林海¹

1.中国石油大学（北京）油气资源与探测国家重点实验室，北京 102249；2.中海油研究总院，北京 100027

收稿日期:2012-06-19 出版日期:2013-08-12 发布日期:2013-08-13
作者简介:陈峥嵘，男，1988年生，硕士，从事石油工程岩石力学和页岩气压裂的研究。
基金资助:
国家自然科学基金资助（No. 51134004）；国家科技重大专项资助（No.2011ZX05024-003-02）。

Research on initiation of oriented perforation fracturing and perforation optimization design method

CHEN Zheng-rong^{1, 2}, DENG Jin-gen¹, ZHU Hai-yan¹, DONG Guang¹, HU Lian-bo¹, LIN Hai¹

1.State Key Laboratory of Petroleum Resources and Prospecting, China University of Petroleum (Beijing), Beijing 102249, China; 2. CNOOC Research Institute, Beijing 100027, China

Received:2012-06-19 Online:2013-08-12 Published:2013-08-13

摘要/Abstract

摘要： 目前定向射孔压裂时起裂压力的预测仅立足于裸眼的情况，忽视套管对起裂压力的影响，在工程应用中将产生较大的误差。考虑套管作用，推导建立定向井井周应力模型。假设地层岩石为张性破坏，并综合以上模型，得到定向射孔井水力压裂起裂压力和起裂角的预测模型。根据该模型编程开发一套定向射孔压裂起裂与射孔优化的软件，可预测定向射孔井的压裂起裂压力和起裂角，并优化选择射孔角度和射孔长度。应用软件对渤海油田三口井进行模拟计算和射孔优化，结果发现，模型的起裂压力预测结果与现场实测结果误差最大仅为4.33%，预测的起裂角也与实际结果相一致，从而验证了本模型的正确性。模型和软件对于现场压裂施工和射孔优化有重要的指导作用。

关键词: 定向射孔, 井周应力, 起裂压力, 射孔优化, 软件

Abstract: In the oriented perforation fracturing, current predicting initiation pressure just considers the naked borehole and neglects the effect of casing, which will lead to the greater errors in the engineering applications. Considering the effect of casing, wellbore stress models of directional well are obtained. According to tensile failure criteria, fracturing initiation pressure and angle models of oriented perforation well are presented. A software is developed, which includes the initiation prediction and perforation optimization of oriented perforation well. The software can predict the initiation pressure and initiation angle of oriented perforation fracturing considering the effect of casing, and optimize the perforation angle and length. Comparing to the actual initiation pressures, the maximum error of the prediction initiation pressures in the software is 4.33% and the predicting initiation angles are consistent with actual initiation angles, so as to prove the accuracy of fracturing initiation pressure and angle models. The models and software can offer instructions to the field fracturing and perforation optimization.

Key words: oriented perforation, stress distribution, initiation pressure, perforation optimization, software

中图分类号:

TE 21

陈峥嵘，邓金根，朱海燕，董光，胡连波，林海 . 定向射孔压裂起裂与射孔优化设计方法研究[J]. , 2013, 34(8): 2309-2315.

CHEN Zheng-rong , DENG Jin-gen , ZHU Hai-yan , DONG Guang , HU Lian-bo , LIN Hai . Research on initiation of oriented perforation fracturing and perforation optimization design method[J]. , 2013, 34(8): 2309-2315.

参考文献

相关文章 15

[1]	韩同春, 林博文, 何露, 苏钰钦, . 基于GIS与数值模拟软件耦合的三维边坡建模方法及其稳定性研究[J]. 岩土力学, 2019, 40(7): 2855-2865.
[2]	董卓, 唐世斌, . 基于最大周向应变断裂准则定向射孔水力裂缝扩展研究[J]. 岩土力学, 2019, 40(11): 4543-4553.
[3]	王志荣，贺平，郭志伟，王永春. 考虑裂缝特性指标的煤层气“垂直井”起裂压力计算方法[J]. , 2018, 39(S1): 369-377.
[4]	夏磊，曾亚武,. 基于PFC2D数值模拟的交替压裂中应力阴影效应研究[J]. , 2018, 39(11): 4269-4277.
[5]	刘振平，杜根明，蔡洁，周凡，刘建，卞康，. 基于MeshPy的3DGIS与三维有限元数值计算无缝耦合方法[J]. , 2018, 39(10): 3841-3852.
[6]	刘汉龙，吴迪，孔纲强，王成龙，吴宏伟，. 预埋与绑扎埋管形式能量桩传热特性研究[J]. , 2017, 38(2): 333-340.
[7]	陈庆发，杨家彩，高远，牛文静，陈大鹏，刘俊广,. 大型复杂地质体三维数值模型构建方法比较研究[J]. , 2016, 37(S2): 753-760.
[8]	杨光华，黄忠铭，姜燕，徐传堡，乔有梁，陈富强, . 深基坑支护双排桩计算模型的改进[J]. , 2016, 37(S2): 1-15.
[9]	胡卸文，刁仁辉，梁敬轩，罗刚，魏来，. 基于CFX的江口沟泥石流危险区范围预测模拟[J]. , 2016, 37(6): 1689-1696.
[10]	王素玲，隋旭，朱永超,. 定面射孔新工艺对水力裂缝扩展影响研究[J]. , 2016, 37(12): 3393-3400.
[11]	霍吉祥，宋汉周. 去耦合方法求解非均质地区地下水中多组分反应-运移模型[J]. , 2015, 36(S2): 57-63.
[12]	陈立强，田守嶒，李根生，范鑫. 超临界CO2压裂起裂压力模型与参数敏感性研究[J]. , 2015, 36(S2): 125-131.
[13]	张志鹏，刘润. 基于GRLWEAP的桩基可打入性影响因素研究[J]. , 2015, 36(S1): 634-638.
[14]	郭建春，何颂根，邓燕. 弹塑性地层水力压裂起裂模式及起裂压力研究[J]. , 2015, 36(9): 2494-2500.
[15]	程亮，卢义玉，葛兆龙，丁红，钟定云，. 倾斜煤层水力压裂起裂压力计算模型及判断准则[J]. , 2015, 36(2): 444-450.

Metrics

Viewed

Full text

Abstract

Cited

Shared

Discussed