大断面宽幅盾构管片三维内力分布分析

›› 2009, Vol. 30 ›› Issue (7): 2058-2062.

大断面宽幅盾构管片三维内力分布分析

张建刚^{1, 2}，何川¹，杨征¹

1.西南交通大学土木工程学院，成都 610031；2.山东农业大学水利土木工程学院，山东泰安 271018

收稿日期:2007-12-12 出版日期:2009-07-10 发布日期:2011-03-10
作者简介:张建刚，男，1974年生，博士研究生，讲师，主要从事盾构隧道设计理论与方法方面的教学和研究工作。
基金资助:
863国家高技术研究发展计划项目（No. 2006AA11Z116）；武汉长江隧道工程专项科研项目（No. WHCJSD/KY/01-01-2005）资助。

Analysis of 3D internal forces distribution of wide segment lining for large-section shield tunnel

ZHANG Jian-gang ^{1, 2}, HE Chuan¹, YANG Zheng¹

1. School of Civil Engineering, Southwest Jiaotong University, Chengdu 610031, China; 2. College of Water Conservancy and Civil Engineering, Shandong Agricultural University, Taian 271018, China

Received:2007-12-12 Online:2009-07-10 Published:2011-03-10

摘要/Abstract

摘要：

以武汉长江隧道工程为例，采用三维壳-弹簧计算模型，对不同幅宽和不同环间接头剪切刚度的管片衬砌结构力学分布进行了分析，并与梁-弹簧模型结果在量值上做了全面比较。研究表明，全环最大弯矩发生在幅宽边缘部位；环间接头剪力对幅宽边缘影响较大，而对幅宽中央影响偏小；当环间接头剪切刚度为非无穷大时，壳模型的幅宽边缘最大弯矩值略微大于梁弹簧模型相应结果，而当无穷大时两者数值则基本相等；壳模型的幅宽中央的最大弯矩值介于梁模型错缝与通缝拼装的数值之间，并随幅宽加大而趋于接近通缝拼装的结果；大幅宽条件下，不宜将梁-弹簧模型的环间最大剪力结果作为环间接头抗剪设计的计算依据。

关键词: 盾构隧道, 管片结构, 壳-弹簧模型, 管片幅宽, 环间接头

Abstract:

Taking the Wuhan Yangtze River tunnel as an engineering background, the internal forces distribution of segment lining structure with different segment widths and different ring joint shear stiffnesses is analyzed by 3Dshell-spring model and compared with the results achieved by beam-spring model. The study shows that: the maximum bending moment on the entire ring always occur on the edge of segment; the ring joint shear force has an great impact on the edge of segment and less in the middle of segment; when the ring joint shear stiffness is non-infinite, the maximum bending moment on the edge of segment calculated by shell-spring model is slightly larger than the results by beam-spring model; and these results almost equal when the joint shear stiffness is infinite; the maximum bending moment in the middle of segment calculated by shell-spring model is between the results by beam-spring model with stagger-jointed and those results by beam-spring model in sequence, and tend to the results in sequence with the segment width increased; when the segment width is large, the maximum shear force between rings calculated by beam-spring model is unfit for shear design of the ring joint.

Key words: shield tunnel, segment lining, shell-spring model, segment width, ring joint

中图分类号:

U 451+.4

张建刚，何川，杨征. 大断面宽幅盾构管片三维内力分布分析[J]. , 2009, 30(7): 2058-2062.

ZHANG Jian-gang, HE Chuan, YANG Zheng. Analysis of 3D internal forces distribution of wide segment lining for large-section shield tunnel[J]. , 2009, 30(7): 2058-2062.

参考文献

相关文章 15

[1]	杨振兴, 陈健, 孙振川, 游永锋, 周建军, 吕乾乾, . 泥水平衡盾构用海水泥浆的改性试验研究[J]. 岩土力学, 2020, 41(2): 501-508.
[2]	魏纲, 张鑫海, 林心蓓, 华鑫欣, . 基坑开挖引起的旁侧盾构隧道横向受力变化研究[J]. 岩土力学, 2020, 41(2): 635-644.
[3]	章定文, 刘志祥, 沈国根, 鄂俊宇, . 超大直径浅埋盾构隧道土压力实测分析及其计算方法适用性评价[J]. 岩土力学, 2019, 40(S1): 91-98.
[4]	张治国, 李胜楠, 张成平, 王志伟, . 考虑地下水位升降影响的盾构施工诱发地层变形和衬砌响应分析[J]. 岩土力学, 2019, 40(S1): 281-296.
[5]	黄大维, 周顺华, 冯青松, 罗锟, 雷晓燕, 许有俊, . 地表均布超载作用下盾构隧道上覆土层竖向土压力转移分析[J]. 岩土力学, 2019, 40(6): 2213-2220.
[6]	莫振泽, 王梦恕, 李海波, 钱勇进, 罗跟东, 王辉, . 粉砂地层中浓泥土压盾构泥膜效应引起的孔压变化规律试验研究[J]. 岩土力学, 2019, 40(6): 2257-2263.
[7]	姚爱军，张剑涛，郭海峰，郭彦非. 地铁盾构隧道上方基坑开挖卸荷-加载影响研究[J]. , 2018, 39(7): 2318-2326.
[8]	钟宇，陈健，陈国良，吴佳明, . 基于建筑信息模型技术的盾构隧道结构信息模型建模方法[J]. , 2018, 39(5): 1867-1876.
[9]	杨文波，陈子全，徐朝阳，晏启祥，何川，韦凯, . 盾构隧道与周围土体在列车振动荷载作用下的动力响应特性[J]. , 2018, 39(2): 537-545.
[10]	康成, 梅国雄, 梁荣柱, 吴文兵, 方宇翔, 柯宅邦, . 地表临时堆载诱发下既有盾构隧道纵向变形分析[J]. 岩土力学, 2018, 39(12): 4605-4616.
[11]	李长俊，陈卫忠，杨建平，刘金泉, . 运营期水下盾构隧道管片接缝张开度变化规律[J]. , 2018, 39(10): 3783-3793.
[12]	魏纲，林雄，金睿，丁智，. 双线盾构施工时邻近地下管线安全性判别[J]. , 2018, 39(1): 181-190.
[13]	姜燕，杨光华，陈富强，徐传堡，张玉成, . 湛江湾高水头跨海盾构隧道管片结构典型断面受力计算与监测反馈分析[J]. , 2018, 39(1): 275-286.
[14]	马春景，姜谙男，江宗斌，王善勇,. 基于单元状态指标的盾构隧道水-力耦合模拟分析[J]. , 2017, 38(6): 1762-1770.
[15]	张晓清，张孟喜，李林，李武祥，王有成,. 多线叠交盾构隧道近距离穿越施工扰动机制研究[J]. , 2017, 38(4): 1133-1140.

Metrics

Viewed

Full text

Abstract

Cited

Shared

Discussed